Flash cosintering of a lanthanum strontium cobalt ferrite nanofibre/Gd-doped ceria bilayer structure

For solid oxide fuel cells, an important structural requirement is that the electrolyte layer needs to be dense and the electrode layer porous, which is difficult to obtain by conventional cosintering. In this work, flash cosintering of a double layer structure consisting of a Gd-doped ceria substrate with a lanthanum strontium cobalt ferrite nanofibre coating is investigated. Experimental and finite element modelling results reveal that when the LSCF layer is connected to the electrode, the heat is concentrated in the LSCF layer, which leads to a huge temperature gradient and introduces severe cracking. When the LSCF layer is electrically isolated from the electrode, the heat is concentrated in the GDC layer, and the temperature gradient is dramatically reduced. In this situation, the density of GDC can reach 92.86% while a high porosity of 52.26% is maintained in the LSCF layer, which is higher than that of the conventional cosintered sample.     

Sealing behaviour of glass-based composites for oxygen transport membranes

In this study, seven different filler materials in different proportions were added to a Ba-Ca-Si glass matrix “H” to investigate new sealant with higher thermal expansion coefficient (CTE) value and good sealing performance for application in oxygen transport membrane (OTM). SrTi_0.75Fe_0.25O_3-δ (STF25) was used as an OTM, and the sealing partners were ferritic steel Aluchrom and pre-oxidized Aluchrom. Compatibility tests were carried out to investigate the feasibility of the composites. Higher CTE values were found in dilatometer tests on composite samples by adding 40 wt% Ag (HAg40) and 30 wt% Ni-Cr (HNC30). Gas-tightness measurements of sandwiched samples produced appropriate helium leakage rates in the range of 10^?6 mbar·l·s^?1. Sealing behaviour of sealants HAg40 and HNC30 were investigated by joining STF25 and as-delivered/pre-oxidized Aluchrom together. Scanning electron microscopy (SEM) on cross-sections of the joints revealed a homogeneous microstructure and good adherence of the glass sealants to support metals and STF25.     

电容式力感知牙周探针设计建模与实验研究

针对当前牙周探针在探诊力控制方面的不足,提出一种基于悬臂梁挠曲效应的差动电容式力感知牙周探针解决方案,设计了探针验证结构,建立了探诊力作用下具有不规则形状的探针工作尖的挠曲模型,导出了探诊力和差动电容之间的求解方程,并通过仿真和实验对模型与方程进行了验证。结果表明,所建立的探针工作尖挠曲模型与静应力仿真结果的最大相对误差不超过±4.5%,所设计的力感知牙周探针多次重复探诊力检测实验的标准差小于均值的0.1%,所导出的求解方程的计算值与实验数据之间趋向一致,以探诊力为拟合权重进行修正后全量程的平均偏差为2.49%,具备进一步产品开发的可行性。     

DC conductivity and AC impedance of Mn doped magnesia alumina spinel (MgAl2-2xMn2xO4) over a large temperature range

MgAl_2-2xMn_2xO₄ (MAMO) with x = 0-0.12 was synthesized in a single-phase form by solid-state reaction. XRD analysis showed that the samples had the cubic center structure of the Fd-3 m space group. Electrical properties of the samples were studied over the temperature range of 300 K∼1073 K. The results showed that the DC conductivity (σ_DC) increased from 10⁻¹¹S/cm at 300 K (MAMO, x = 0) to 10^-3S/cm at 1073 K (MAMO, x = 0.12). The equivalent circuit of the complex impedance spectra suggested that the relaxation of charge carriers was of non-Debye type. The conduction was mainly caused by grain boundaries and the capacitance was mainly attributed to polarization. The complex permittivity values (ε’ and ε’’) were increased by two orders of magnitude with the increase in Mn content and temperature over the measured frequency range (1 Hz-1 MHz). Therefore, doping with Mn could be applied to modify the electrical properties of MAMO at high temperature.     

Carbon vacancies improved photocatalytic hydrogen generation of g-C3N4 photocatalyst via magnesium vapor etching

Vacancies engineering was widely reported as the promising strategy for the improvement of the photocatalytic performance of semiconductor photocatalysts. In current work, carbon vacancies are constructed successfully in graphitic carbon nitride (g-C₃N₄) photocatalyst via magnesium vapor etching. Experimental results show that the formed carbon vacancies in g-C₃N₄ photocatalyst can significantly improve the photocatalytic H₂ generation performance. XRD, FTIR, SEM/TEM, XPS and PL characterization data are employed to evidence the construction of carbon vacancies, which are revealed to be the reason for the enhancement of photocatalytic H₂ evolution. This work develops an alternative route to construct carbon vacancies in g-C₃N₄ materials and gives an insight into the influence of vacancies on the photocatalytic performance of photocatalysts.     

In situ fabrication of TiC-NiCr cermets by selective laser melting

In situ synthesis of TiC-NiCr cermets during selective laser melting (SLM) was investigated. Powder mixture consisting Ti, C and Ni80Cr20 solid solution was prepared by milling process to attain the nominal composition of TiC-40 wt% NiCr. Feedstock powder was milled for 7 h by a high energy ball mill. SLM process was applied at three scanning speeds and the effect of input energy density on phase formation, microstructure and hardness of resultant samples was evaluated. Morphology of the powders and microstructure of in situ fabricated cermets were investigated by field emission electron microscopy (FESEM), and structural evolution during SLM was studied by X-ray diffractometery (XRD). The results showed that TiC can be synthesized during SLM process even at relatively low energy densities and the formation mechanism of TiC phase is affected by the input energy density. Relative density of the samples increased from 88.24% to 98.53% with increasing the energy density from 138.7 to 346.7 Jmm⁻³. The sample fabricated by SLM process using the maximum energy density of 346.7 Jmm⁻³showed the highest mean microhardness value of 1289 HV.     

Effect of strain path change on the through-thickness microstructure during tantalum rolling

High purity tantalum was respectively processed by unidirectional rolling (UR) and clock rolling (CR), and the through-thickness microstructures were investigated by multiple characterization techniques including electron backscatter diffraction (EBSD), Vickers hardness (HV) and X-ray diffraction (XRD). Results show that the through-thickness stored energy distribution in CR specimens is more homogeneous than in UR specimens due to uniform texture distribution. {111} grains possess larger Schmid factors and the corresponding Schmid factor difference ratio than {100} grains, indicating the activation of uniserial slipping in {111} grains, which leads to inhomogeneous deformation and higher stored energy. Besides, X-ray line profile analysis (XLPA) suggests that the stored energy of {111} grains increases successively from the surface to center layer, regardless of strain paths, due to the influence of redundant friction on the surface layers. While the occurrence of multiple slipping in {100} grains leads to homogeneous deformation and lower stored energy.     

Ti-48Al-2Nb-2Cr合金热变形行为及本构关系研究

采用Gleeble-1500热力模拟机对铸态Ti-48Al-2Nb-2Cr合金进行高温变形热压缩试验,变形温度范围为1050~1200℃,应变速率范围为0.001~0.1s^-1,压缩变形量为60%。研究该合金高温变形温度和应变速率与流变应力之间的关系,计算了合金激活能,并建立了Ti-48Al-2Nb-2Cr合金的Arrhenius本构模型和多元线性回归的本构模型。结果表明,该合金的激活能随温度升高和应变速率增大而增大;Arrhenius本构模型的相关系数为0.98228,平均相对误差为9.97%,相对误差在10%以内的点只占62.0%;而采用多元线性回归本构模型的相关系数为0.99566,平均相对误差为4.76%,相对误差在10%以内的点占92.6%,本构精度较高。     

Microstructure and properties of WC-12Co composite coatings prepared by laser cladding

A comprehensive study of the phase composition, microstructure evolution, microhardness and wear performance of WC-12Co composite coatings fabricated by laser cladding using coaxial powder-feed mode was presented. It was shown that a combination of high scan speed and high laser energy density made WC on the edge of WC-12Co composite powders partially melt in liquid Co and 304 stainless steel matrix, and then new carbides consisting of lamellar WC and herringbone M₃W₃C (M=Fe, Co) were formed. Meanwhile, WC-12Co composite coatings with no porosity, cracks and drawbacks like decarburization were obtained, showing high densification and good metallurgical bonding with the substrate. Furthermore, a considerably high microhardness of HV_0.3 1500-1600, low coefficient of friction of 0.55 and wear rate of (2.15±0.31)×10^-7 mm³/(N·m) were achieved owing to the synergistic effect of excellent metallurgical bonding and fine microstructures of composite coating under laser power of 1500 W.     

Study on inhomogeneous cooling behavior of extruded profile with unequal and large thicknesses during quenching using thermo-mechanical coupling model

The interfacial heat transfer coefficient between hot profile surface and cooling water was determined by using inverse heat conduction model combined with end quenching experiment. Then, a Deform-3D thermo-mechanical coupling model for simulating the on-line water quenching of extruded profile with unequal and large thicknesses was developed. The temperature field, residual stress field and distortion of profile during quenching were investigated systematically. The results show that heat transfer coefficient increases as water flow rate increases. The peak heat transfer coefficient with higher water flow rates appears at lower interface temperatures. The temperature distribution across the cross-section of profile during quenching is severe nonuniform and the maximum temperature difference is 300 °C at quenching time of 3.49 s. The temperature difference through the thickness of different parts of profile first increases sharply to a maximum value, and then gradually decreases. The temperature gradient increases obviously with the increase of thickness of parts. After quenching, there exist large residual stresses on the inner side of joints of profile and the two ends of part with thickness of 10 mm. The profile presents a twisting-type distortion across the cross-section under non-uniform cooling and the maximum twisting angle during quenching is 2.78°.